Click Here

 

Do you find yourself hunting for help and advice around A Step-by-Step Guide to Installing a Bathtub?

Setting up a tub isn't precisely rocket science, yet it does need strong plumbing, woodworking, and occasionally, tiling skills. Replacing an old tub with a new one is also a moderately difficult project. If the old bathtub is easily obtainable, the task can relocate speedily; if you have to open a wall to get rid of the old tub as well as position the brand-new tub, the task is a lot harder. In either situation, the project is within a home handyman's abilities, although you will certainly need a helper to move out the old tub and also set in the new one. Make certain you have actually certified yourself for the task as well as fit trying it. Rather than employing a professional to take control of a halfway-completed job, it is far better to think about using one before you begin. Chances are you might require an expert plumber to make tube connections.
This article will certainly assist you set up a new bath tub in your shower room if you have currently gotten a new tub as well as don't require to transform the arrangement of your previous water system pipes.
Your devices and also product list should make up the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Tape Measure


• Pipeline Caps


 

Removing Old Taps

If you require to change old faucets with new ones as a part of your installation, after that the first thing you ought to do is disconnect the water system. After doing so, turn on the taps to drain pipes any kind of water staying in the system. The process of getting rid of the existing taps can be quite troublesome because of the restricted accessibility that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the faucets. Have a cloth ready for the continuing to be water that will originate from the pipelines. When the supply pipelines have actually been eliminated, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming throughout this process. When the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing substance.
Prior to carrying on to fit the new faucets, compare the pipeline connections on the old taps to the brand-new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.

 

 

Fitting New Touches

If the tails of the brand-new faucets are plastic, then you will certainly need a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the tap as well as the other end offers a link to the existing supply pipes.
If you require to fit a monobloc, after that you will call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, position the faucet in the installing opening in the bath/basin ensuring that the washers are in area in between the faucet and the sink. Protect the tap in position with the maker given backnut. As soon as the faucet is safely in place, the supply pipes can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular tap ports. The previous kind should be attached to the faucet ends initially, tightening up just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.

 

 

Mounting the Bath tub

Making use of the two wooden boards under its feet, place the bath tub in the needed position. The wooden boards are useful in evenly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 little factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as readjusting the feet on the tub up until the level reads level.
To set up taps, fit all-time low of the furthest versatile faucet adapter to the proper supply pipeline by making a compression sign up with; then do the very same for the other tap.
Turn on the supply of water as well as check all joints as well as brand-new pipework for leakages as well as tighten them if needed. Fill the tub as well as also check the overflow electrical outlet and also the regular electrical outlet for leakages.
Finally, repair the bathroom paneling as defined in the maker's user's manual. Tiling and sealing around the bathtub ought to wait until the tub has been made use of at least once as this will resolve it into its last placement.

 

 

Getting ready for the Setup

First of all, the sustaining framework provided with the bathroom should be fitted (if called for) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to see to it that if the tap comes with a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets unit to avoid strain on the bath tub.
Fit the flexible faucet connectors to the bottom of the two taps making use of 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom need to currently be ready to be suited its last placement.

 

 

Tiling Around the Bathtub

In the location where the bath meets the tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the fitting can move enough to split a rigid seal, creating the water to pass through the wall in between the bath and the tiling, bring about issues with moisture as well as feasible leakages to the ceiling listed below.
You can select from a range of coloured sealers to blend in your components and installations. They are sold in tubes and also cartridges, and also are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of drenched paper or soft rope. Remember to always fill the tub with water before securing, to permit the movement experienced when the tub is in use. The sealant can fracture rather very early if you do not consider this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily available on the marketplace. It is suggested to fit the ceramic tiles using water-resistant or water-proof glue as well as grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I found that blog posting on Installing A Bathtub when doing a search on the web. Loved our article? Please share it. Help someone else find it. I am grateful for your time. Please check our blog back soon.

Drain woes? Connect.